Home > News Details
  • Lattice Structured Impact Absorber With Embedded Antiicing

    The present paper introduces an innovative lattice structure [] working as impact absorber and embedded anti-icing/de-icing system for wing leading edges ().Such a structure involves the main benefits of AM applied to aerospace industry as described before.

    Consultation details
  • Improving Refinery Gas Processing Unit Performance With

    Absorber and move to an amine unit for amine treatment before finally entering the refinery fuel gas system. Back at the absorber deethanizer, the heavier components that leave the bottom of the absorber tower enter a series of fractionators that separate the mixture of heavier components into purified streams to be used by other processes.

    Consultation details
  • Optimization Of Amine Sweetening Units BRE

    Figure 1 represents a simple amine treating facility. Sour gas is introduced in the absorber where it contacts lean amine solution traveling down the column. The acid gas components, H 2S and CO 2, are absorbed by the amine solution and the sweet gas leaves the absorber for further processing. The rich amine is sent to a flash tank and.

    Consultation details
  • Amine System Foaming In The Natural Gas Processing Industry

    In the natural gas processing industry amines are used to remove acidic gases such as CO 2 and H 2 S from the inlet feed (natural gas) before the gas is further processed. A persistent operational problem in the gas sweetening industry is amine system foaming.

    Consultation details
  • Multisorb To Introduce Jerkyfresh Oxygen Absorber System At

    Multisorb Technologies will introduce its complete system solution for extending the shelf life of jerky products at the International Production & Processing Expo (IPPE 2016) in Atlanta, GA, January 26-28, 2016.

    Consultation details
  • Dehydration With Glycol Petrowiki

    The rich glycol leaving the absorber must be regenerated to a high purity so that it can be recirculated to the absorber to continue its dehydration function. The regeneration is accomplished in the reboiler and the still column above the reboiler.

    Consultation details
  • Gas Absorber | Protocol

    This system only has one stage and poor mass transfer rates, but is very effective for solutes with high liquid solubility 1. The goal of this experiment is to determine how variables including gas flow rate, water flow rate, and carbon dioxide concentration affect the overall mass transfer coefficient in a gas absorber.

    Consultation details
  • Gas Treating (Refinery Natural Gas) ADIP Process

    Integration of gas treating with the SCOT solvent system is an option. Description: The H2S-containing gas is contacted counter-currently in an absorption column with ADIP solvent. The regenerated solvent is introduced at the top of the absorber.

    Consultation details
  • Fuel Processing System An Overview | Sciencedirect Topics

    Z. Ilsen ?nsan, Ahmet K. Avci, in Fuel Cells: Technologies for Fuel Processing, 2011. Publisher Summary. This chapter discusses reactor designs for fuel processing. Fuel reforming reactor is the part of the fuel processing system in which catalytic conversion of hydrocarbon fuels (fossil or renewable) to a hydrogen-rich mixture takes place.

    Consultation details
  • Laser Processing Of 3M? EMI Absorber AB5020HF ULS

    Processing Example 3M EMI Absorber AB5020HF applications requiring fine geometry and intricate detail without degrading the physical properties of the material can be achieved with the MultiWave Hybrid technology. An example demonstrating the results of laser cutting AB5020HF using the recommended system configuration is shown in Figure 5.

    Consultation details
  • Optimize Capacity And Efficiency For An Amine Unit

    Optimize capacity and efficiency for an amine unit M. Pieronek, P. Krouskop and B. Burr, Bryan Research and Engineering Inc., Bryan, Texas; and S. Kitsatienkun, PTT, plc, Rayong, Thailand The removal of carbon dioxide (CO 2 ) from natural gas is a necessary treating step prior to cryogenic processing.

    Consultation details
  • Natural Gas Processing

    Processing. 2. Description of a Natural Gas Processing System: An Overview Natural gas processing and the removal of various components from it tend to involve the most complex and expensive processes. All of the H2S and most of the water vapor, CO2, and N2 must be removed first.

    Consultation details
  • Multisorb To Introduce Jerkyfresh? Oxygen Absorber System At

    Multisorb Technologies ) will introduce its complete system solution for extending the shelf life of jerky products at the International Production & Processing Expo (IPPE 2016) in Atlanta, GA, January 26-28, 2016. The Multisorb JerkyFresh system includes both oxygen absorbers to extend shelf life and dispensing equipment.

    Consultation details
  • Benfield Process

    Chemical Mechanism in the Absorber and Regenerator. The chemical reactions between the acid gases and K2CO3 are well known, These reactions are reversible. They proceeds from left to right in the Absorber unit and from right to left in the Regeneration unit. Steady-state processing.

    Consultation details
  • Wet Flue Gas Desulfurization (FGD) Systems Gas Absorbers

    A typical lime/limestone Flue Gas Desulfurization (FGD) system consists of three major sub-systems: The reagent (lime or limestone slurry) preparation; The scrubber/SO2 absorber and mist eliminator, and slurry/solid waste disposal systems.

    Consultation details
  • Amineunit Startup Illustrates Commissioning Considerations

    Refining & Processing; MDEA's heat of solution with CO 2 in the absorber tower was lower (575 btu leads to system water loss-makeup water added to the absorber's washing section can be.

    Consultation details
  • Lean Oil Absorption Process | Hydrocarbon Compression

    The absorber is a contact tower, similar in design to the glycol contact tower. The lean absorber oil trickles down over trays or packing while the gas flows upward counter current to the absorber oil. The gas leaves the top of the absorber while the absorber oil, now rich in light hydrocarbons from the gas, leaves the bottom of the absorber.

    Consultation details
  • LOCAT?: A Flexible Hydrogen Sulfide Removal Process

    Figure 1. LO-CAT DirectTreat Processing Configuration . When using the DirectTreat configuration, the entrained liquids are removed prior to introducing the “sour” gas stream to the absorber. In this scheme, equations 1, 2 and 3 occur in the absorber while equation 4 occurs in the oxidizer.

    Consultation details
  • Microwave Absorber Evaluation

    Performance with absorber unit / ferrite), and uses NA. The reflection of specification 10-120MHz: S11/S22 and penetration S21 measurement. It requests by measuring and processing as follows; 1)The absorber installed part calibrates the measurement system as open/short-circuited. 2)Put the EUT and the S parameter measure for absorber.

    Consultation details
  • Absorbers Laser Beam Diagnostics Laser Mechanisms Inc

    In these cases 99% of the radiation must be absorbed. Many beam sources therefore contain a PRIMES absorber. Laser material processing systems in which the machining process does not completely absorb the laser radiation or the radiation must be “captured” (for example during a workpiece changeover) pose a similar challenge.

    Consultation details
  • An Evaluation Of General Rules Of Thumb In Amine Sweetening

    50C. Two things should be noted. First, all four streams are fed to the absorber at 40C and are saturated with water. Since condensing a non-aqueous phase is of concern, the hydrocarbon dew point is what is most important and is shown in Table 1. Second, some practical limitations for the system must not be ignored.

    Consultation details
  • Terms Used In The Gas Processing Industry

    Convergence pressure: The pressure at a given temperature for a hydrocarbon system of fixed composition at which the vapor-liquid equilibrium K-values of the various components in the system become, or tend to become, unity. The convergence pressure is used to adjust vapor-liquid equilibrium K-values to the particular system under consideration.

    Consultation details
  • Glycol Dehydration Wikipedia

    Glycol dehydration is a liquid desiccant system for the removal of water from natural gas and natural gas liquids (NGL). It is the most common and economical means of water removal from these streams.

    Consultation details
  • Chapter 5 Absorption And Stripping

    Entering into the absorber flows at a rate of 500 kmol/h with yA = 0.3 and leaving the absorber with yA = 0.01. Solvent enters the absorber at the rate of of 1500 kmol/h with xA = 4 Geankoplis, C.J., Transport Processes and Separation Process Principles , 4 th edition, Prentice Hall, 2003, pg. 988.

    Consultation details
  • The Glycol Dehydration Process: A Basic Overview Oil And

    Glycol dehydration is a key component of the overall process that can’t be skipped over. I’ll discuss another major form in a later post but I’ve always find the process of glycol dehydration fascinating. I hope you have enjoyed learning a little more about the next step in the gas processing system. By: Shawn Gipson.

    Consultation details
  • Glycol Dehydration Wikipedia

    Glycol dehydration is a liquid desiccant system for the removal of water from natural gas and natural gas liquids (NGL). It is the most common and economical means of water removal from these streams. Glycols typically seen in industry include triethylene glycol (TEG), diethylene glycol (DEG), ethylene glycol (MEG), and tetraethylene glycol (TREG). TEG is the most commonly used glycol in industry.

    Consultation details
  • Benfield Process

    They proceeds from left to right in the Absorber unit and from right to left in the Regeneration unit. Steady-state processing. Ideal mass balance is achieved when the CO2 and H2S moles absorbed from the Sour Gas equals the CO2 and H2S moles exiting with the Acid Gas. Deviation from ideal mass balance will occur if CO2, H2S, and also H2O.

    Consultation details
  • Amine System Foaming In The Natural Gas Processing

    In the natural gas processing industry amines are used to remove acidic gases such as CO 2 and H 2 S from the inlet feed (natural gas) before the gas is further processed. A persistent operational problem in the gas sweetening industry is amine system foaming.

    Consultation details
  • Amine Gas Treating Wikipedia

    Amine gas treating, also known as amine scrubbing, gas sweetening and acid gas removal, refers to a group of processes that use aqueous solutions of various alkylamines (commonly referred to simply as amines) to remove hydrogen sulfide (H 2 S) and carbon dioxide (CO 2) from gases. It is a common unit process used in refineries, and is also used in petrochemical plants, natural gas processing.

    Consultation details
  • Amine Gas Sweetening Systems

    Be vented, incinerated, or directed to a sulfur recovery system. 8. Hot regenerated lean amine is cooled in a solvent aerial cooler and circulated to the contactor tower, completing the cycle. 9. A variety of heat sources can be used for the still reboiler—direct fired, waste heat, hot oil, and steam systems. Amine Gas Sweetening Systems.

    Consultation details
  • Absorbers Laser Beam Diagnostics Laser Mechanisms Inc

    Many beam sources therefore contain a PRIMES absorber. Laser material processing systems in which the machining process does not completely absorb the laser radiation or the radiation must be “captured” (for example during a workpiece changeover) pose a similar challenge. PRIMES absorbers are used in these instances as beam dumps.

    Consultation details